[Oct-2022] Check your preparation for Cisco 350-401 On-Demand Exam
Practice Exam 350-401 Realistic Dumps Verified Questions
Infrastructure (30%)
- Troubleshooting static and dynamic 802.1q trunking protocols as well as static & dynamic EtherChannels;
- Configuring first-hop redundancy protocols such as VRRP & HSRP.
- Defining the main use and principles cases for Layer 2 & Layer 3 roaming;
- Defining the AP modes and antenna types;
- Configuring and verifying Spanning Tree Protocols (MST & RSTP);
- Describing the access point detection and join process;
- Describing Network Time Protocol;
- Comparing the routing concepts of OSPF & EIGRP;
Why Choose Onpassitsure Cisco Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 Dump?
Effective Learning Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 certification is an essential part of the IT corporate world. Explanation of 350-401 real questions is very important in this regard. The IMINS 350-401 exam dumps are the most reliable source of knowledge in this field.
We guarantee your Cisco 350-401 Exam success with the help of our Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 exam dumps. Our 350-401 exam dumpsbase pdf tests will help you pass the Managing Industrial Networks with Cisco Networking Technologies (IMINS) Cisco 350-401 Exam through your first try. Our Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 PDF exam dumps have been updated regularly to make sure that it covers the latest 350-401 exam. Cisco 350-401 Dumps are the most reliable solution for your Managing Industrial Networks with Cisco Networking Technologies (IMINS) Cisco 350-401 Exam success. We offer you a money-back guarantee if you are not satisfied with our training. Our Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 PDF exam dumps can clear all your doubts about the Managing Industrial Networks with Cisco Networking Technologies (IMINS) Cisco 350-401 Exam. We have 24/7 online support for Managing Industrial Networks with Cisco Networking Technologies (IMINS) Cisco 350-401 Exam. We provide a fast download speed of Managing Industrial Networks with the Cisco Networking Technologies (IMINS) Cisco 350-401 Exam. Configuring Cisco IOS Network Devices (ICND) 200-101 Exam PDF is provided in the Managing Industrial Networks with Cisco Networking Technologies (IMINS) 350-401 PDF exam dumps.
Further Certification Path After Passing 350-401
The Cisco 350-401 ENCOR certification exam is the starting point for different certifications. If you want to go further than being a certified Specialist for Enterprise Core, then you should know that it is also a core exam for the CCNP Enterprise certificate. From here, you will need to take a concentration test to get accredited.
If CCNP accreditation is not the final target point for you, then use Cisco 350-401 ENCOR as the qualifying exam to obtain CCIE Enterprise Infrastructure or Enterprise Wireless accreditation. These will require you to ace one more test as well.
NEW QUESTION 95 
Refer to the exhibit. An engineer must deny HTTP traffic from host A to host V while allowing all other communication between the hosts, drag and drop the commands into the configuration to achieve these results. Some commands may be used more than once. Not all commands are used.
Answer:
Explanation:
NEW QUESTION 96
Which tunneling technique is used when designing a Cisco SD-Access fabric data plane?
- A. VRF Lite
- B. VRF
- C. LISP
- D. VXLAN
Answer: D
Explanation:
The tunneling technology used for the fabric data plane is based on Virtual Extensible LAN (VXLAN). VXLAN encapsulation is UDP based, meaning that it can be forwarded by any IP-based network (legacy or third party) and creates the overlay network for the SD-Access fabric. Although LISP is the control plane for the SD-Access fabric, it does not use LISP data encapsulation for the data plane; instead, it uses VXLAN encapsulation because it is capable of encapsulating the original Ethernet header to perform MAC-in-IP encapsulation, while LISP does not. Using VXLAN allows the SD-Access fabric to support Layer 2 and Layer 3 virtual topologies (overlays) and the ability to operate over any IP-based network with built-in network segmentation (VRF instance/VN) and built-in group-based policy.
NEW QUESTION 97
Refer to the exhibit.
Which configuration allows Customer2 hosts to access the FTP server of Customer1 that has the IP address of
192.168.1.200?
- A. ip route vrf Customer1 172.16.1.1 255.255.255.255 172.16.1.1 global
ip route vrf Customer 192.168.1.200 255.255.255.0 192.168.1.1 global
ip route 192.168.1.0 255.255.255.0 Vlan10
ip route 172.16.1.0 255.255.255.0 Vlan20 - B. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 Customer1 ip route vrf Customer 192.168.1.200 255.255.255.255 192.168.1.1 Customer2
- C. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 global
ip route vrf Customer 192.168.1.200 255.255.255.255 192.168.1.1 global
ip route 192.168.1.0 255.255.255.0 Vlan10
ip route 172.16.1.0 255.255.255.0 Vlan20 - D. ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 Customer2 ip route vrf Customer 192.168.1.200 255.255.255.255 192.168.1.1 Customer1
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200158-Configure-Route-Leaking-between-Global-a.h
Static routes directly between VRFs are not supported so we cannot configure a direct static route between two VRFs.
The command "ip route vrf Customer1 172.16.1.0 255.255.255.0 172.16.1.1 global" means in VRF Customer1, in order to reach destination 172.16.1.0/24 then we uses the next hop IP address 172.16.1.1 in the global routing table. And the command "ip route 192.168.1.0 255.255.255.0 Vlan10" tells the router "to reach 192.168.1.0/24, send to Vlan 10".
NEW QUESTION 98
Drag and drop the characteristics from the left onto the protocols they apply to on the right?
Answer:
Explanation:
Explanation
Diagram Description automatically generated
NEW QUESTION 99
Drag and drop the characteristics from the left onto the appropriate infrastructure deployment types on the right.
Answer:
Explanation:
NEW QUESTION 100
Refer to the exhibit.
A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are mode, the port channel does not establish. Based on the configuration excerpt of SW3, what is the cause of the problem?
- A. The port-channel interface lead balance should be set to src-mac
- B. The port-channel should be set to auto.
- C. The port channel on SW2 is using an incompatible protocol.
- D. The port-channel trunk is not allowing the native VLAN.
Answer: C
NEW QUESTION 101
Refer to the exhibit.
A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish. Based on the configuration excerpt of SW3, what is the cause of the problem?
- A. The port-channel should be set to auto.
- B. The port channel on SW2 is using an incompatible protocol.
- C. The port-channel interface load balance should be set to src-mac
- D. The port-channel trunk is not allowing the native VLAN.
Answer: B
NEW QUESTION 102
Which LISP device is responsible for publishing EID-to-RLOC mappings for a site?
- A. ITR
- B. ETR
- C. MS
- D. MR
Answer: B
Explanation:
An Egress Tunnel Router (ETR) connects a site to the LISP-capable part of a core network (such as the Internet), publishes EID-to-RLOC mappings for the site, responds to Map-Request messages, and decapsulates and delivers LISP-encapsulated user data to end systems at the site.
Reference:
3s/irl-xe-3s-book/irl-overview.html
NEW QUESTION 103
Refer to the exhibit.
An engineer must establish eBGP peering between router R3 and router R4. Both routers should use their loopback interfaces as the BGP router ID. Which configuration set accomplishes this task?
- A. R3(config)#router bgp 200
R3(config-router)#neighbor 10.24.24.4 remote-as 100
R3(config-router)#neighbor 10.24.24.4 update-source Loopback0
R4(config)#router bgp 100
R4(config-router)#neighbor 10.24.24.3 remote-as 200
R4(config-router)#neighbor 10.24.24.3 update-source Loopback0 - B. R3(config)#router bgp 200
R3(config-router)#neighbor 10.24.24.4 remote-as 100
R3(config-router)#bgp router-id 10.3.3.3
R4(config)#router bgp 100
R4(config-router)#neighbor 10.24.24.3 remote-as 200
R4(config-router)#bgp router-id 10.4.4.4 - C. R3(config)#router bgp 200
R3(config-router)#neighbor 10.4.4.4 remote-as 100
R3(config-router)# neighbor 10.4.4.4 update-source Loopback0
R4(config)#router bgp 100
R4(config-router)#neighbor 10.3.3.3 remote-as 200
R4(config-router)#network 10.3.3.3 update-source Loopback0 - D. R3(config)#router bgp 200
R3(config-router)#neighbor 10.4.4.4 remote-as 100
R3(config-router)#bgp router-id 10.3.3.3
R4(config)#router bgp 100
R4(config-router)#neighbor 10.3.3.3 remote-as 200
R4(config-router)#bgp router-id 10.4.4.4
Answer: B
NEW QUESTION 104
IS OSPF, which LAS type is responsible for pointing to the ASBR router?
- A. type 1
- B. type 4
- C. type 3
- D. type 2
Answer: B
NEW QUESTION 105
Refer to the exhibit.
An engineer must allow all users In the 10.2.2.0/24 subnet to access the Internet. To conserve address space, the public interface address of 209.165.201.1 must be used for all external communication. Which command set accomplishes these requirements?
A)
B)
C)
D)
- A. Option C
- B. Option D
- C. Option B
- D. Option A
Answer: B
Explanation:
Explanation
The command ip nat inside source list 10 interface G0/3 overload configures NAT to overload (PAT) on the address that is assigned to the G0/3 interface.
NEW QUESTION 106
Refer to the exhibit
Communication between London and New York is down Which to resolve this issue?
A)
B)
C)
D)
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: A
Explanation:
Explanation
https://learningnetwork.cisco.com/s/question/0D53i00000Ksyty/tostastns-tottattnt
NEW QUESTION 107
Which component handles the orchestration plane of the Cisco SD-WAN?
- A. vBond
- B. vSmart
- C. vEdge
- D. vManage
Answer: A
Explanation:
Explanation
+ Orchestration plane (vBond) assists in securely onboarding the SD-WAN WAN Edge routers into the SD-WAN overlay. The vBond controller, or orchestrator, authenticates and authorizes the SD-WAN components onto the network. The vBond orchestrator takes an added responsibility to distribute the list of vSmart and vManage controller information to the WAN Edge routers. vBond is the only device in SD-WAN that requires a public IP address as it is the first point of contact and authentication for all SD-WAN components to join the SD-WAN fabric. All other components need to know the vBond IP or DNS information.
NEW QUESTION 108
Drag and drop the characteristics from the left onto the correct infrastructure deployment types on the right.
Answer:
Explanation:
Explanation
On premise: customizable,specific requirements,resources
Cloud: scale, built-in automated backup, strong stable internet
NEW QUESTION 109
Refer to the exhibit.
An engineer must ensure that all traffic leaving AS 200 will choose Link 2 as the exit point. Assuming that all BGP neighbor relationships have been formed and that the attributes have not been changed on any of the routers, which configuration accomplish task?
- A. R3(config-router)neighbor 10.1.1.1 weight 200
- B. R3(config-router)bgp default local-preference 200
- C. R4(config-router)nighbor 10.2.2.2 weight 200
- D. R4(config-router)bgp default local-preference 200
Answer: D
Explanation:
Explanation
Local preference is an indication to the AS about which path has preference to exit the AS in order to reach a certain network. A path with a higher local preference is preferred. The default value for local preference is 100.
Unlike the weight attribute, which is only relevant to the local router, local preference is an attribute that routers exchange in the same AS. The local preference is set with the "bgp default local-preference value" command.
In this case, both R3 & R4 have exit links but R4 has higher local-preference so R4 will be chosen as the preferred exit point from AS 200.
NEW QUESTION 110
Refer to the exhibit.
Which type of antenna does the radiation pattern represent?
- A. directional patch
- B. Yagi
- C. omnidirectional
- D. multidirectional
Answer: B
Explanation:
Explanation
A Yagi antenna is formed by driving a simple antenna, typically a dipole or dipolelike antenna, and shaping the beam using a well-chosen series of non-driven elements whose length and spacing are tightly controlled.
Reference: https://www.cisco.com/c/en/us/products/collateral/wireless/aironetantennas- accessories/prod_white_paper0900aecd806a1a3e.htm
NEW QUESTION 111
Drag and drop the characteristics from the left onto the correct infrastructure deployment types on the right.
Answer:
Explanation:
Explanation
On premise: customizable,specific requirements,resources
Cloud: scale, built-in automated backup, strong stable internet
NEW QUESTION 112
......
Valid 350-401 Dumps for Helping Passing Cisco Exam: https://www.prepawaypdf.com/Cisco/350-401-practice-exam-dumps.html
Download Free Cisco 350-401 Exam Questions & Answer: https://drive.google.com/open?id=1KLGG0FbUV_6ZBJuou2aFaRqZ6OwQnHkZ