Verified NACE-CIP1-001 Dumps Q&As - NACE-CIP1-001 Test Engine with Correct Answers
Pass Your NACE-CIP1-001 Dumps as PDF Updated on 2025 With 100 Questions
NEW QUESTION # 24
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. blistering.
- B. cracking.
- C. checking.
- D. alligatoring.
Answer: C
NEW QUESTION # 25
What is used to determine compressed air cleanliness?
- A. Psychrometer
- B. Profilometer
- C. Needle pressure gauge
- D. Blotter test
Answer: B
NEW QUESTION # 26
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a detailed checklist and document the lack of a standard.
- B. NACE 2/SSPC SP10
- C. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- D. their best judgment based on similar projects and specifications.
Answer: C
NEW QUESTION # 27
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION # 28
Conventional spray is a good choice when:
- A. High viscosity coatings are being applied
- B. High production rates are required
- C. High transfer efficiency is required
- D. High quality finishes are required
Answer: D
NEW QUESTION # 29
An inspectors personal log book should contain:
- A. The inspector's personal opinions of the application team
- B. No comments regarding the application team
- C. Objective comments regarding the application work
- D. Subjective comments re ding the application team
Answer: B
NEW QUESTION # 30
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. sagging.
- B. checking.
- C. cracking.
- D. holiday.
Answer: D
NEW QUESTION # 31
To achieve consistently accurate results with ALL alt test equipment
- A. calibrate the instrument in the field.
- B. avoid placing the sample discs on a surface.
- C. wash your hands before sampling.
- D. wear gloves when sampling.
Answer: C
NEW QUESTION # 32
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Atmospheric Corrosion
- B. Galvanic Corrosion
- C. Localized Corrosion
- D. General Corrosion
Answer: B
NEW QUESTION # 33
The Inspector's Log Book is generally:
- A. Submitted to the client upon project completion
- B. Shared with all parties upon project completion
- C. Shredded by the inspector upon project completion
- D. Retained by the inspector upon project completion
Answer: D
NEW QUESTION # 34
NACE SP 0178 is a standard for:
- A. Stainless steel pipe to be Externally Coated
- B. Structural steel to be coated for Atmospheric Service
- C. Tanks and Vessels to be Externally Coated
- D. Tanks and Vessels to, be Lined for Immersion Service
Answer: D
NEW QUESTION # 35
The NACE Inspector should perform tests for soluble salts:
- A. After surface preparation
- B. When specified
- C. Prior to coating application
- D. Prior to surface preparation
Answer: B
NEW QUESTION # 36
If inspectors identify issues of non-conformance during an inspection, they should
- A. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. instruct the contractor's personnel in how to correct the issue so the project is not delayed
Answer: A
NEW QUESTION # 37
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Use the job specification as a guide
- C. Use the product data sheet as a guide
- D. Call the person who wrote the specification for clarification
Answer: B
NEW QUESTION # 38
Digital hygrometers
- A. use a thermocouple in contact with the surface to measure temperature
- B. are used to measure temperature from a distance.
- C. determine relative humidity, air temperature, and dew point temperature:
- D. consist of a bimetallic sensing element protected from wind gusts.
Answer: C
NEW QUESTION # 39
Stripe coats are best applied by:
- A. High volume low pressure spray
- B. Brush
- C. Airless spray
- D. Conventional spray
Answer: B
NEW QUESTION # 40
Polymerization is the process of:
- A. Monomers telegraphing
- B. All thermoplastic coatings
- C. Monomers joining together
- D. All organic coatings
Answer: C
NEW QUESTION # 41
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 225 Gauge Readings resulting in 75 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 105 Gauge Readings resulting in 35 Spot Measurements
Answer: A
NEW QUESTION # 42
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Assume the role of the Safety Inspector
- C. Check the credentials of the Safety Officer on site
- D. Check the PPE used by the Applicators
Answer: A
NEW QUESTION # 43
......
Pass NACE NACE-CIP1-001 Exam Info and Free Practice Test: https://www.prepawaypdf.com/NACE/NACE-CIP1-001-practice-exam-dumps.html
NACE NACE-CIP1-001 Real Exam Questions and Answers FREE: https://drive.google.com/open?id=1no0LV5Pi6ZKWA_RuzrLSMhZ7qDdRylom