Try CFI-I Free Now! Real Exam Question Answers Updated [Dec 01, 2025]
Get Ready to Pass the CFI-I exam with NFPA Latest Practice Exam
NEW QUESTION # 56
The following types of systems are addressed within the scope of NFPA 25, Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems EXCEPT
- A. Sprinklers
- B. Wet chemical
- C. Foam water
- D. Standpipe and hose
Answer: B
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Scope of NFPA 25:
NFPA 25 specifically covers the inspection, testing, and maintenance of water-based fire protection systems.
These include:
Sprinkler systems
Standpipe and hose systems
Foam-water systems
Water spray systems
Option C (Wet Chemical):
Wet chemical systems are not water-based; they fall under NFPA 17A (Standard for Wet Chemical Extinguishing Systems).
Wet chemical systems are typically used in kitchen fire suppression systems where they extinguish fires involving grease or oil.
Other Options Explained:
Option A (Sprinklers): Addressed by NFPA 25.
Option B (Standpipe and hose): Addressed by NFPA 25.
Option D (Foam water): Foam-water systems use water to mix and distribute foam and are within NFPA 25's scope.
Summary:
Wet chemical systems are not covered by NFPA 25, as it only applies to water-based fire protection systems.
NEW QUESTION # 57
The authorization to issue permits is granted by the
- A. state legislature.
- B. authority having jurisdiction.
- C. Fire Inspection Handbook.
- D. NFPA 101, Life Safety Code.
Answer: B
Explanation:
The authority having jurisdiction (AHJ) is the entity responsible for enforcing codes, standards, and regulations, including the authorization to issue permits.
The AHJ is defined as the organization, office, or individual responsible for approving plans, issuing permits, and ensuring compliance.
While state legislatures (A) may create laws, the actual enforcement and issuance of permits are delegated to the AHJ.
Fire Inspection Handbooks (C) and NFPA 101 (D) are reference tools but do not directly grant authority.
Reference:
NFPA 1, Fire Code, Section 3.2.2: Defines the AHJ's role and responsibilities.
NFPA 101: Acknowledges the AHJ as the enforcement body.
NEW QUESTION # 58
What is the maximum volume of Class I, Class II, and Class III A liquids allowed to be stored in an individual storage cabinet?
- A. 100 gal (379 L)
- B. 140 gal (530 L)
- C. 80 gal (303 L)
- D. 120 gal (460 L)
Answer: D
Explanation:
The maximum volume of flammable and combustible liquids permitted in an individual storage cabinet is addressed by NFPA 30, Flammable and Combustible Liquids Code. Specifically:
Class I liquids are flammable liquids with flashpoints below 100°F (37.8°C).
Class II and IIIA liquids are combustible liquids with higher flashpoints but still pose significant fire hazards when improperly stored.
According to NFPA 30, Section 9.5.2, the maximum allowable quantity of Class I, II, and IIIA liquids in a storage cabinet is 120 gallons (460 liters).
Why 120 gallons?
The 120-gallon limit is determined based on:
The need to minimize fire risk and contain potential ignition sources.
Storage cabinets are designed to limit vapor emissions and resist fire exposure for a minimum duration (e.g., 10 minutes per OSHA standards).
Additional Considerations:
Cabinets must meet construction requirements outlined in NFPA 30, Chapter 9 (e.g., self-closing doors, ventilation, and fire resistance).
Exceeding the 120-gallon limit would require additional fire safety measures or a different storage approach (e.g., a flammable liquid storage room).
Reference:
NFPA 30, Flammable and Combustible Liquids Code, Section 9.5.2
OSHA 1910.106(d)(3): Storage requirements for flammable and combustible liquids.
NEW QUESTION # 59
Smoking is prohibited within what minimum distance from an outdoor hazardous material storage facility or dispensing area?
- A. 100 ft (30.4 m)
- B. 25 ft (7.6 m)
- C. 50 ft (15.2 m)
- D. 10 ft (3.4 m)
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Smoking Prohibition Near Hazardous Materials:
According to NFPA 1 (Fire Code), Section 60.5.2.3, smoking is prohibited within a minimum of 50 feet (15.2 m) from outdoor hazardous material storage facilities or dispensing areas to reduce fire risks from ignition sources.
Why 50 Feet is Required:
Hazardous materials can release flammable vapors that ignite easily. The 50-foot distance ensures safety by minimizing the risk of exposure to open flames or sparks.
Other Options Explained:
Option A (10 ft) and Option B (25 ft): Too close to ensure safety.
Option D (100 ft): More than required under NFPA 1.
Summary:
Smoking is prohibited within 50 feet (15.2 m) of outdoor hazardous material storage or dispensing areas.
NEW QUESTION # 60
What is the acceptable flow of water normally required for a pipe schedule sprinkler system that has a minimum pressure of 20 psi (14 bar) in an ordinary hazard occupancy?
- A. 700-1,000 gpm (2,650-3,785 L/min)
- B. 500-750 gpm (1,893-2,839 L/min)
- C. 1,750-2,000 gpm (6,624-7,571 L/min)
- D. 850-1,500 gpm (3,218-5,678 L/min)
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Pipe Schedule Sprinkler Systems:
According to NFPA 13 (Standard for the Installation of Sprinkler Systems), Table 11.2.3.2.1, the required flow rate for ordinary hazard occupancies is typically 850-1,500 gpm (3,218-5,678 L/min) at a minimum pressure of 20 psi (14 bar).
Ordinary Hazard Occupancies:
These include areas with moderate fire loads, such as manufacturing spaces or storage areas, where a higher water flow is required compared to light hazard occupancies.
Other Options Explained:
Option A (500-750 gpm): Insufficient for ordinary hazard occupancies; more suited to light hazard classifications.
Option B (700-1,000 gpm): Too low for larger or higher-risk ordinary hazard areas.
Option D (1,750-2,000 gpm): Exceeds the typical requirement for ordinary hazards.
Summary:
The acceptable flow for a pipe schedule sprinkler system in an ordinary hazard occupancy is 850-1,500 gpm (3,218-5,678 L/min) at 20 psI .
NEW QUESTION # 61
What is the minimum acceptable flow at the base of the riser for a pipe-schedule sprinkler system in an ordinary hazard (Group 1) occupancy?
- A. 850 gpm (3,218 L/min)
- B. 500 gpm (1,893 L/min)
- C. 250 gpm (946 L/min)
- D. 700 gpm (2,649 L/min)
Answer: B
Explanation:
For a pipe-schedule sprinkler system, the minimum water flow at the base of the riser depends on the occupancy hazard classification, as defined in NFPA 13.
For Ordinary Hazard (Group 1) occupancies, the minimum required flow at the base of the riser is 500 gpm (1,893 L/min).
The 500 gpm flow ensures sufficient water supply to the sprinkler system to suppress fires involving moderate combustibles.
Higher flows (e.g., 700 gpm and 850 gpm) are required for more severe hazards (e.g., Extra Hazard occupancies).
Reference:
NFPA 13, Table 11.2.3.1.1: Minimum flow requirements for pipe-schedule systems.
NEW QUESTION # 62
The appropriateness of the safeguards required by the Life Safety Code to individual buildings and structures bears due regard to all EXCEPT which of the following?
- A. Age of the building
- B. Capabilities of the occupants
- C. The fire load of the occupancy
- D. Number of persons exposed
Answer: A
Explanation:
The Life Safety Code (NFPA 101) ensures that fire and life safety safeguards are appropriate to the risks posed by a building or occupancy. Key considerations include:
Fire load of the occupancy (B): The quantity and combustibility of materials influence fire severity and spread.
Number of persons exposed (C): Occupant load determines evacuation requirements and system capacities.
Capabilities of the occupants (D): Includes factors like mobility, age, and ability to respond to emergencies.
The age of the building (A) is not a primary factor under the Life Safety Code. Safeguards apply regardless of a building's age, as older buildings may still require updates to meet current safety standards.
Reference:
NFPA 101, Section 4.6.6: Considerations for applying safeguards in buildings and structures
NEW QUESTION # 63
In a low hazard occupancy, what is the maximum allowable travel distance to a Class A portable fire extinguisher?
- A. 100 ft (30.5 m)
- B. 30 ft (9.1 m)
- C. 75 ft (22.8 m)
- D. 50 ft (15.2 m)
Answer: C
Explanation:
The maximum allowable travel distance to a Class A portable fire extinguisher in a low hazard occupancy is governed by NFPA 10, Standard for Portable Fire Extinguishers.
Class A hazards involve ordinary combustibles such as paper, wood, cloth, and certain plastics.
In low hazard occupancies (e.g., office buildings, schools), where the fire risk is minimal, the maximum travel distance to a Class A extinguisher is 75 feet (22.8 meters).
The 75-foot distance ensures that fire extinguishers are readily accessible in the event of a fire while maintaining practicality for building layouts.
30 ft (A) applies to more hazardous areas with specific requirements.
50 ft (B) is applicable for Class B extinguishers in moderate hazards.
100 ft (D) exceeds NFPA 10 limits for Class A hazards.
Reference:
NFPA 10, Section 6.2.1.2: Travel distance requirements for Class A fire extinguishers.
NEW QUESTION # 64
Which one of the following is a primary reason for issuing a permit?
- A. To establish the economic feasibility of a project
- B. To allow the requester to meet less restrictive code requirements
- C. To meet fire insurance requirements
- D. To make the jurisdiction aware of potentially hazardous situations or conditions
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Purpose of Permits:
Permits are issued primarily to ensure the jurisdiction (Authority Having Jurisdiction - AHJ) is aware of potentially hazardous situations or conditions and can enforce compliance with fire and safety codes.
Permits also provide an opportunity to inspect operations, processes, or structures to ensure safety.
NFPA References:
According to NFPA 1 (Fire Code), permits are required for activities that could pose risks, such as hazardous materials, fire protection system installations, and occupancy changes.
Other Options Explained:
Option A (To meet fire insurance requirements): Permits are not issued for insurance purposes, although compliance may indirectly affect insurance.
Option C (Less restrictive code requirements): Permits are not for bypassing codes.
Option D (Economic feasibility): Economic factors are unrelated to the permitting process.
Summary:
Permits are issued to make the jurisdiction aware of potentially hazardous situations or conditions and ensure compliance with fire safety regulations.
NEW QUESTION # 65
After conducting the annual test of a dry barrel hydrant, what is the maximum length of time permitted for full drainage to take place?
- A. 30 minutes
- B. 15 minutes
- C. 60 minutes
- D. 10 minutes
Answer: B
Explanation:
Dry barrel hydrants must be tested annually to ensure proper drainage and operation. According to NFPA 25, Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems:
After testing, full drainage of the hydrant must occur within 15 minutes. This ensures no residual water remains in the hydrant barrel, which could freeze in cold climates and damage the hydrant.
If the hydrant fails to drain within 15 minutes, it indicates an obstruction or malfunction in the drainage system that must be corrected.
10 minutes (A): Not enough time for standard drainage.
30 minutes (C) and 60 minutes (D): Exceed the acceptable limit defined by NFPA 25.
Reference:
NFPA 25, Section 7.3.2: Annual testing and drainage requirements for dry barrel hydrants.
NEW QUESTION # 66
What is the minimum number of separate and remote means of egress in a new assembly occupancy with an occupant load greater than 1,000?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Egress Requirements for Assembly Occupancies:
According to NFPA 101 (Life Safety Code), Section 12.2.4.1, a new assembly occupancy with an occupant load exceeding 1,000 people requires a minimum of 4 separate and remote means of egress.
Why Four Egress Routes Are Required:
Larger occupant loads increase the risk of congestion during an evacuation.
Multiple egress routes ensure occupants can safely evacuate without crowding or delays.
Other Options Explained:
Option A (1), Option B (2), and Option C (3):
These options do not meet the requirements for occupant loads exceeding 1,000 in new assembly occupancies.
Summary:
A new assembly occupancy with an occupant load greater than 1,000 requires a minimum of 4 separate and remote means of egress to ensure safe evacuation.
NEW QUESTION # 67
At what minimum pressure would automatic sprinkler piping be hydrostatically tested if the maximum system pressure is 175 psi (12 bar)?
- A. 225 psi (15.5 bar)
- B. 250 psi (17 bar)
- C. 200 psi (13.8 bar)
- D. 175 psi (12 bar)
Answer: C
Explanation:
According to NFPA 13, Standard for the Installation of Sprinkler Systems, all sprinkler piping must undergo a hydrostatic test to verify its strength and leak resistance.
Hydrostatic testing must be conducted at a pressure of 200 psi (13.8 bar) or 50 psi (3.4 bar) greater than the system's maximum working pressure, whichever is higher.
Since the maximum system pressure is 175 psi, the test pressure must be at least 200 psI .
175 psi (A) is the system pressure, not the test pressure.
225 psi (C) and 250 psi (D) exceed the required test pressure.
Reference:
NFPA 13, Section 25.2.1.1: Hydrostatic test requirements for sprinkler piping.
NEW QUESTION # 68
Which of the following is true regarding the copy of an issued permit?
- A. It shall be readily accessible at each place of operation.
- B. It shall be transferable to a new address.
- C. It shall be maintained by the architect of record.
- D. It shall be reissued upon completion of the project.
Answer: A
Explanation:
Permits are required to document authorization for specific fire protection and safety activities. According to NFPA 1, Fire Code, and general permit guidelines:
Issued permits must be readily accessible at the location of the operation to ensure:
Inspectors can verify compliance with the permit requirements.
The permit holder demonstrates authorization for ongoing work.
Reissuing a permit after completion of a project (B) is not standard practice.
Permits are not the responsibility of architects (C) unless they are the permit holder.
Permits are generally non-transferable (D) because they are site-specific and operation-specific.
Reference:
NFPA 1, Fire Code, Section 1.12.13: Permit requirements for accessibility and non-transferability.
NEW QUESTION # 69
The acceptance of a permit as defined in the fire code gives the authority having jurisdiction the right to enter the premises to inspect
- A. at any time.
- B. on a quarterly cycle.
- C. with the permission of the owner.
- D. at reasonable times.
Answer: D
Explanation:
The right of entry for inspections is governed by NFPA 1, Fire Code:
The Authority Having Jurisdiction (AHJ) is granted the right to enter and inspect premises at reasonable times to ensure compliance with the conditions of the permit and fire safety regulations.
The term "reasonable times" ensures that inspections are conducted without causing unnecessary disruption to occupants or operations.
"With the permission of the owner" (A) is not required under the fire code since permits inherently authorize inspection.
Quarterly cycle (B) is not defined in the fire code and depends on the nature of the permit.
At any time (D) would be unreasonable unless immediate danger is suspected.
Reference:
NFPA 1, Section 1.7.7: Right of entry for fire inspections.
NEW QUESTION # 70
Prior to conducting a fire flow test of a water distribution system, a responsible person from what department should be notified?
- A. Water department
- B. Highway department
- C. Fire department
- D. Health department
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Fire Flow Tests:
Fire flow tests are conducted to determine the available water supply for firefighting and to ensure water distribution systems meet fire protection requirements.
Who Should Be Notified:
According to NFPA 291 (Recommended Practice for Fire Flow Testing and Marking of Hydrants), the water department must be notified prior to conducting fire flow tests.
This is because the water department oversees the water distribution system and needs to monitor for any disruptions, water loss, or pressure changes caused by the test.
Other Options Explained:
Option A (Fire department): Fire departments conduct or participate in the tests but do not need to be the primary department notified.
Option B (Highway department): Not involved in water system management.
Option D (Health department): Concerned with water quality, not water flow or system capacity.
Summary:
The water department must be notified prior to a fire flow test to ensure proper coordination and monitoring of the water distribution system.
NEW QUESTION # 71
What NFPA code or standard would be used to answer an inquiry regarding the minimum required water temperature for a sprinkler system's water storage tanks?
- A. NFPA 101
- B. NFPA 72
- C. NFPA 13
- D. NFPA 25
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Sprinkler System Design and Installation:
NFPA 13 (Standard for the Installation of Sprinkler Systems) provides detailed guidance on the design, installation, and requirements for water storage tanks, including minimum water temperature to prevent freezing in cold climates.
Other Options Explained:
Option B (NFPA 25): Focuses on inspection, testing, and maintenance of systems, not design parameters.
Option C (NFPA 72): Covers fire alarm systems, not sprinkler systems.
Option D (NFPA 101): Addresses life safety issues, not sprinkler system specifics.
Summary:
Use NFPA 13 to determine the minimum required water temperature for sprinkler system storage tanks.
NEW QUESTION # 72
Records regarding fire prevention inspections must include all of the following EXCEPT
- A. a summary of violations found during the inspection
- B. the date of the inspection
- C. photographs of code violations
- D. dates of the service of notices
Answer: C
Explanation:
Fire prevention inspection records must include essential details to ensure a proper record of the inspection process and enforcement of fire codes. According to NFPA 1, Fire Code, and standard fire inspection procedures:
Summary of violations found (A): This provides a clear record of noncompliance issues identified during the inspection.
Date of the inspection (B): The inspection date is mandatory for tracking inspection schedules and enforcement timelines.
Dates of the service of notices (C): These dates are necessary to document when violations were communicated to the responsible party.
Photographs of code violations (D): While photographs can be useful for documentation, they are not a mandatory requirement under NFPA standards for inspection records.
Reference:
NFPA 1, Fire Code, Chapter 1: Documentation requirements for fire inspection records.
NEW QUESTION # 73
How much clear space shall be maintained around the circumference of a fire hydrant (except as otherwise required or approved)?
- A. 24 in. (610 mm)
- B. 60 in. (1524 mm)
- C. 48 in. (1219 mm)
- D. 36 in. (914 mm)
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Clear Space Requirements for Fire Hydrants:
According to NFPA 1 (Fire Code), Section 18.5.7.1, a clear space of at least 36 inches (914 mm) must be maintained around the circumference of a fire hydrant.
Why 36 Inches is Required:
Maintaining 36 inches of clear space ensures that fire hydrants are:
Readily accessible for firefighters during emergencies.
Free from obstructions that may hinder operation or connection of hoses.
Other Options Explained:
Option A (24 in): Insufficient clearance; may obstruct hydrant accessibility.
Option C (48 in) and Option D (60 in): More than required; not mandated by NFPA 1.
Summary:
A 36-inch (914 mm) clear space must be maintained around the circumference of a fire hydrant to ensure accessibility and operability.
NEW QUESTION # 74
Which of the following classifications of liquids indicates a flash point at or above 200°F (93°C)?
- A. Class II
- B. Class IIIA
- C. Class IC
- D. Class IIIB
Answer: D
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Liquid Classification by Flash Point:
Per NFPA 30 (Flammable and Combustible Liquids Code):
Class IC: Flash point below 73°F but above 100°F.
Class II: Flash point between 100°F and 140°F.
Class IIIA: Flash point between 140°F and 200°F.
Class IIIB: Flash point at or above 200°F (93°C).
Why Class IIIB Applies:
Class IIIB liquids, with higher flash points, are considered less flammable and less likely to ignite under normal conditions.
Other Options Explained:
Option A (Class IC): Flash point below 100°F.
Option B (Class II): Flash point below 140°F.
Option C (Class IIIA): Flash point below 200°F.
Summary:
A Class IIIB liquid has a flash point at or above 200°F (93°C).
NEW QUESTION # 75
What is the maximum occupant load for a conference room with a total area of 900 ft² (84 m²)?
- A. 120 people
- B. 60 people
- C. 30 people
- D. 90 people
Answer: B
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Occupant Load Calculation:
According to NFPA 101 (Life Safety Code), Table 7.3.1.2, for assembly occupancies without fixed seating (such as conference rooms), the occupant load factor is:
15 ft² (1.4 m²) per person.
Calculation:
Divide the total area of 900 ft² by 15 ft per person: 900ft2/15ft2/person=60people900 \, \text{ft}^2 \, / \, 15 \, \text{ft}^2/\text{person} = 60 \, \text{people}900ft2/15ft2/person=60people Other Options Explained:
Option A (30 people): Too low.
Option C (90 people) and Option D (120 people): Exceed the calculated occupant load.
Summary:
The maximum occupant load for a 900 ft² conference room is 60 people.
NEW QUESTION # 76
Where shall fire department connections on wet-pipe automatic sprinkler systems be located?
- A. On the suction side of booster pumps
- B. On the system side of the water supply check valve
- C. Above the dry-pipe valve on a single-riser dry-pipe system
- D. On the supply side of the check valve in a single-riser system
Answer: B
Explanation:
The placement of the fire department connection (FDC) for a wet-pipe automatic sprinkler system is governed by NFPA 13, Standard for the Installation of Sprinkler Systems.
The FDC must be located on the system side of the water supply check valve (A). This ensures that the fire department can pump water into the system effectively and directly supply the sprinkler system during an emergency.
Suction side of booster pumps (B): This placement would not supply water correctly to the system during firefighting operations.
Supply side of the check valve (C): This would prevent water from entering the sprinkler system since the check valve blocks backflow from the FDC.
Above the dry-pipe valve (D): This applies to dry-pipe systems, not wet-pipe systems.
Reference:
NFPA 13, Section 8.17.2.4: Location requirements for fire department connections.
NEW QUESTION # 77
Business occupancies are required to hold practice fire drills if the occupant load exceeds 500 or if the number of occupants above or below street level exceeds how many people?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
Fire Drills in Business Occupancies:
According to NFPA 101 (Life Safety Code), Section 39.7.2, business occupancies must conduct fire drills if:
The total occupant load exceeds 500 people, or
The number of occupants above or below street level exceeds 200 people.
Why 200 People is the Threshold:
Occupants above or below the street level face increased risks during evacuation due to longer egress times and potential congestion on stairs or pathways.
Regular fire drills ensure occupants are familiar with evacuation procedures.
Other Options Explained:
Option A (100), Option B (150), and Option D (250):
These values do not align with NFPA 101 requirements for occupant load thresholds in business occupancies.
Summary:
Fire drills are required when the number of occupants above or below street level exceeds 200 in business occupancies.
NEW QUESTION # 78
A vehicle fuel dispenser for LP-Gas, installed under a weather shelter or canopy, shall not be enclosed by more than what percentage of its perimeter?
- A. 25 percent
- B. 10 percent
- C. 50 percent
- D. 75 percent
Answer: C
Explanation:
Comprehensive and Detailed Step-by-Step Explanation:
LP-Gas Fuel Dispenser Requirements:
According to NFPA 58 (Liquefied Petroleum Gas Code), Section 6.24.3.14, a vehicle fuel dispenser for LP-Gas under a weather shelter or canopy shall not be enclosed by more than 50 percent of its perimeter.
Reason for Limiting Enclosure:
Proper ventilation is required to prevent the accumulation of LP-Gas vapors, which are heavier than air and can pose an explosion hazard if confined.
Other Options Explained:
Option A (10 percent) and Option B (25 percent): Too restrictive; adequate ventilation can be achieved with up to 50% enclosure.
Option D (75 percent): Exceeds the allowable limit and may trap vapors, creating a hazard.
Summary:
LP-Gas vehicle fuel dispensers under a shelter or canopy shall not be enclosed by more than 50 percent of their perimeter.
NEW QUESTION # 79
......
NFPA CFI-I Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
Pass Your Next CFI-I Certification Exam Easily & Hassle Free: https://www.prepawaypdf.com/NFPA/CFI-I-practice-exam-dumps.html
Get Prepared for Your CFI-I Exam With Actual NFPA Study Guide!: https://drive.google.com/open?id=1EoHx0lr1bzRgoWwR9xlbn-I9sJWcx1cY