Most UptoDate Facebook 100-101 Exam Dumps PDF 2024
100% Free Digital Marketing Associate 100-101 Dumps PDF Demo Cert Guide Cover
Facebook 100-101 (Meta Certified Digital Marketing Associate) Certification Exam is an excellent opportunity for anyone looking to enhance their digital marketing skills and knowledge, especially when it comes to Facebook advertising. With the certification, you can demonstrate your expertise in the field and gain a competitive edge in the job market.
NEW QUESTION # 28
Refer to the exhibit.
The network is converged.After link-state advertisements are received from Router_A, what information will Router_E contain in its routing table for the subnets 208.149.23.64 and 208.149.23.96?
- A. 208.149.23.64[110/1] via 190.172.23.10, 00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10, 00:00:16, FastEthemet0/0
- B. 208.149.23.64[110/13] via 190.173.23.10, 00:00:07, Serial1/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, Serial1/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, FastEthemet0/0
- C. 208.149.23.64[110/13] via 190.173.23.10, 00:00:07, FastEthemet0/0 208.149.23.96[110/13] via 190.173.23.10, 00:00:16, FastEthemet0/0
- D. 208.149.23.64[110/3] via 190.172.23.10, 00:00:07, Serial1/0 208.149.23.96[110/3] via 190.173.23.10, 00:00:16, Serial1/0
Answer: C
Explanation:
Explanation Router_E learns two subnets subnets 208.149.23.64 and 208.149.23.96 via Router_A through FastEthernet interface. The interface cost is calculated with the formula 108 / Bandwidth. For FastEthernet it is 108 / 100 Mbps = 108 / 100,000,000 = 1. Therefore the cost is 12 (learned from Router_A) + 1 = 13 for both subnets -> The cost through T1 link is much higher than through T3 link (T1 cost = 108 / 1.544 Mbps = 64; T3 cost = 108 / 45 Mbps = 2) so surely OSPF will choose the path through T3 link -> Router_E will choose the path from Router_A through FastEthernet0/0, not Serial1/0. In fact, we can quickly eliminate answers B, C and D because they contain at least one subnet learned from Serial1/0 -> they are surely incorrect.
NEW QUESTION # 29
What will the daily budget spend be when running ads?
- A. The maximum amount that an advertiser is willing to spend over the duration of the campaign
- B. The exact amount that an advertiser is willing to spend over the duration of the campaign
- C. The total amount that an advertiser is willing to spend over the duration of the campaign
- D. The average amount that an advertiser is willing to spend per day over the duration of the campaign
Answer: A
NEW QUESTION # 30
What is the best practice when assigning IP addresses in a small office of six hosts?
- A. Assign the addresses statically on each node.
- B. Use a DHCP server that is located at the headquarters.
- C. Use a DHCP server that is located at the branch office.
- D. Assign the addresses by using the local CDP protocol.
Answer: A
Explanation:
Explanation/Reference:
Its best to use static addressing scheme where the number of systems is manageable
rather than use dynamic protocol as it is easy to operate and manage.
NEW QUESTION # 31
Two routers named Atlanta and Brevard are connected by their serial interfaces as shown in the exhibit, but there is no data connectivity between them. The Atlanta router is known to have a correct configuration.
Given the partial configurations shown in the exhibit, what is the problem on the Brevard router that is causing the lack of connectivity?
- A. The maximum transmission unit (MTU) size is too large.
- B. The bandwidth setting is incompatible with the connected interface.
- C. The subnet mask is incorrect.
- D. The IP address is incorrect.
- E. The serial line encapsulations are incompatible.
- F. A loopback is not set.
Answer: D
Explanation:
Topic 8, OSPF Questions
NEW QUESTION # 32
Refer to the topology and switching table shown in the graphic.
Host B sends a frame to Host C.
What will the switch do with the frame?
- A. send the frame out all ports except port 0/2
- B. drop the frame
- C. return the frame to Host B
- D. send an ARP request for Host C
- E. record the destination MAC address in the switching table and send the frame directly to Host C
- F. send an ICMP Host Unreachable message to Host B
Answer: A
Explanation:
Topic 2, LAN Switching Technologies
NEW QUESTION # 33
Refer to the exhibit.
Host A is sending a packet to Host B for the first time. What destination MAC address will Host A use in the ARP request?
- A. 255.255.255.255
- B. 00-19-d3-2d-c3-b2
- C. 192.168.0.1
- D. 172.16.0.50
- E. 00-17-94-61-18-b0
- F. ff-ff-ff-ff-ff-ff
Answer: F
Explanation:
For the initial communication, Host A will send a broadcast ARP (all F's) to determine the correct address to use to reach the destination.
NEW QUESTION # 34
A window washing company delivers a campaign to generate sign-ups for its email marketing Which metric should the company use to evaluate the success of the campaign?
- A. Traffic
- B. Conversions
- C. Leads
- D. Clicks
Answer: A
NEW QUESTION # 35
A business recently delivered an ad campaign with the Brand Awareness objective on the Facebook App Which metric within Ads Manager will help the business determine the success of the campaign?
- A. Amount spent
- B. Reach
- C. Estimated Ad Recall Lift Rate
- D. Cost per click
Answer: B
NEW QUESTION # 36
Refer to the exhibit.
Mary is sending an instant message to Robert. The message will be broken into a series of packets that will traverse all network devices. What addresses will populate these packets as they are forwarded from Router1 to Router2?
- A. Option B
- B. Option D
- C. Option A
- D. Option E
- E. Option C
Answer: A
Explanation:
The Source and Destination IP address is not going to change. Host 1 IP address will stay as being the source IP and the Host 2 IP address will stay the destination IP address. Those two are not going to change. For the MAC address it is going to change each time it goes from one hope to another. (Except switches... they don't change anything) Frame leaving HOST 1 is going to have a source MAC of Host 1 and a destination MAC of Router
1.Router 1 is going to strip that info off and then will make the source MAC address of Router1's
exiting interface, and making Router2's interface as the destination MAC address.
Then the same will happen... Router2 is going to change the source/destination info to the source
MAC being the Router2 interface that it is going out, and the destination will be Host2's MAC
address.
NEW QUESTION # 37
When configuring NAT, the Internet interface is considered to be what?
- A. global
- B. outside
- C. local
- D. inside
Answer: B
Explanation:
Explanation/Reference:
Network address translation or NAT requires the Internet to be considered as an outside
interface else it won't serve the purpose it intends to.
NEW QUESTION # 38
Which two options does an advertiser choose when creating a Lookalike Audience? (Choose 2)
- A. Audience size
- B. Demographics
- C. Source audience
- D. Interests
Answer: A,C
NEW QUESTION # 39
A retailer has new campaign assets for an upcoming spring collection. They want to offer an immersive post click experience that allows viewers to swipe through and took at video, photo and text formats in one ad.
Which creative format should the retailer use?
- A. Reels
- B. Instant experience
- C. Stories
- D. In stream video
Answer: B
NEW QUESTION # 40
An advertiser is creating new assets and wants to inspire their audience with entertaining content that is easily discoverable on Reels.
Which format should the advertiser create?
- A. Vertical image
- B. Vertical video
- C. Horizontal image
- D. Horizontal video
Answer: D
NEW QUESTION # 41
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?
- A. the OSPF route
- B. all three routes
- C. the OSPF and RIPv2 routes
- D. the RIPv2 route
- E. the EIGRP route
Answer: E
Explanation:
Explanation/Reference:
When one route is advertised by more than one routing protocol, the router will choose to
use the routing protocol which has lowest Administrative Distance. The Administrative
Distances of popular routing protocols are listed below:
NEW QUESTION # 42
Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.)
- A. VLANs
- B. PoE
- C. redundant components
- D. port security
- E. layer 3 support
Answer: A,D
Explanation:
http://www.ciscopath.com/content/61/
http://www.mcmcse.com/cisco/guides/hierarchical_model.shtml Access layer The main purpose of the access layer is to provide direct connection to devices on the network and controlling which devices are allowed to communicate over it. The access layer interfaces with end devices, such as PCs, printers, and IP phones, to provide access to the rest of the network. The access layer can include routers, switches, bridges, hubs, and wireless access points (AP).
Switch features in the Access layer: Port security VLANs Fast Ethernet/Gigabit Ethernet Power over Ethernet (PoE) Link aggregation Quality of Service (QoS)
------
NEW QUESTION # 43
Refer to the exhibit.
The network administrator made the entries that are shown and then saved the configuration. From a console connection, what password or password sequence is required for the administrator to access privileged mode on Router1?
- A. either cisco or sanjose
- B. sanjose
- C. cisco
- D. either cisco or sanfran
- E. sanfran
- F. sanjose and sanfran
Answer: E
Explanation:
The enable secret password takes precedence over the enable password, so sanfran will be used.
NEW QUESTION # 44
Which one of the following IP addresses is the last valid host in the subnet using mask 255.255.255.224?
- A. 192.168.2.61
- B. 192.168.2.32
- C. 192.168.2.60
- D. 192.168.2.63
- E. 192.168.2.62
Answer: E
Explanation:
With the 224 there are 8 networks with increments of 32 One of these is 32 33 62 63 where 63 is broadcast so 62 is last valid host out of given choices.
NEW QUESTION # 45
A network administrator cannot connect to a remote router by using SSH. Part of the show interfaces command is shown.
router#show interfaces
Serial0/1/0 is up, line protocol is down
At which OSI layer should the administrator begin troubleshooting?
- A. network
- B. physical
- C. transport
- D. data link
Answer: D
Explanation:
Explanation/Reference: https://learningnetwork.cisco.com/thread/12389
I think the indication here is "Serial 0 is up, line protocol is down". What causes this indication? Correct me if I am wrong. When you have this indication, a cable unplugged is not a correct answer. If you check the output of your "show interface serial 0" command again, you should notice it as "Serial 0 is down, line protocol is down. Under the "show ip int brief" you should see status = down and protocol = down as opposed to up, down. Because you disconnected the cable, layer 1 will go down, which is indicated by the serial 0 down status. The line protocol status is for layer 2. So, a cable unplugged is not a correct answer to "Serial 0 is up, line protocol is down". Hope this helps.
NEW QUESTION # 46 
The hosts in the LAN are not able to connect to the Internet. Which commands will correct this issue?
- A. Option B
- B. Option D
- C. Option A
- D. Option E
- E. Option C
Answer: A
Explanation:
Explanation/Reference:
Do a "show ip int brief" and you will see that Fa0/1 has an IP address assigned, but it is
shut down.
NEW QUESTION # 47
Refer to the exhibit.
A TFTP server has recently been installed in the Atlanta office. The network administrator is located in the NY office and has made a console connection to the NY router. After establishing the connection they are unable to backup the configuration file and IOS of the NY router to the TFTP server. What is the cause of this problem?
- A. The TFTP server has an incorrect IP address.
- B. The NY router has an incorrect subnet mask.
- C. The network administrator computer has an incorrect IP address.
- D. The TFTP server has an incorrect subnet mask.
Answer: D
Explanation:
Explanation/Reference:
The subnet mast of the TFTP server needs to be in tune with the other network
requirements else it won't be possible.
NEW QUESTION # 48
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
- A. There is an area ID mismatch.
- B. There is an OSPF hello and dead interval mismatch.
- C. There is a PPP authentication issue; a password mismatch.
- D. There is a missing network command in the OSPF process on R5.
Answer: B
Explanation:
The "show ip ospf interface command on R3 and R5 shows that the hello and dead intervals do not match. They are 50 and 200 on R3 and 10 and 40 on R5.
NEW QUESTION # 49 
Select two options which are security Issues which need to be modified before RouterA is used? (Choose two.)
- A. inappropriate wording in banner message
- B. configuration supports un-secure web server access
- C. unencrypted weak password is configured to protect privilege mode
- D. virtual terminal lines have a password, but it will not be used
- E. the virtual terminal lines have a weak password configured
Answer: A,D
Explanation:
(this answer can be done by simulation only, don't know user name password and banner message etc)
NEW QUESTION # 50
Refer to the exhibit.
Why are two OSPF designated routers identified on Core-Router?
- A. The router at 208.149.23.130 is a secondary DR in case the primary fails.
- B. Core-Router is connected to more than one multi-access network.
- C. Two router IDs have the same OSPF priority and are therefore tied for DR election
- D. The DR election is still underway and there are two contenders for the role.
Answer: B
Explanation:
Explanation/Reference:
OSPF elects one DR per multi-access network. In the exhibit there are two DR so there
must have more than one multi-access network.
NEW QUESTION # 51
Which address type does a switch use to make selective forwarding decisions?
- A. destination MAC address
- B. source IP address
- C. destination IP address
- D. source and destination IP address
- E. source MAC address
Answer: A
Explanation:
Switches analyze the destination MAC to make its forwarding decision since it is a layer 2 device. Routers use the destination IP address to make forwarding decisions.
NEW QUESTION # 52
CORRECT TEXT
Answer:
Explanation:
Router>enable
Router#config terminal
Router(config)#hostname Apopka
2) Enable-secret password (cisco10):
Apopka(config)#enable secret cisco10
3) Set the console password to RouterPass:
Apopka(config)#line console 0
Apopka(config-line)#password RouterPass
Apopka(config-line)#login
Apopka(config-line)#exit
4) Set the Telnet password to scan90:
Apopka(config)#line vty 0 4
Apopka(config-line)#password scan90
Apopka(config-line)#login
Apopka(config-line)#exit
5) Configure Ethernet interface (on the right) of router Apopka:
The subnet mask of the Ethernet network 209.165.201.0 is 27. From this subnet mask, we can
find out the increment by converting it into binary form, that is /27 = 1111 1111.1111 1111.1111
1111.1110 0000. Pay more attention to the last bit 1 because it tells us the increment, using the
formula:
Increment = 2place of the last bit 1 (starts counting from 0,from right to left), in this case increment
= 25 = 32. Therefore:
Increment: 32
Network address: 209.165.201.0
Broadcast address: 209.165.201.31 (because 209.165.201.32 is the second subnetwork, so the
previous IP - 209.165.201.31 - is the broadcast address of the first subnet).
-> The second assignable host address of this subnetwork is 209.165.201.2/27
Assign the second assignable host address to Fa0/0 interface of Apopka router:
Apopka(config)#interface Fa0/0
Apopka(config-if)#ip address 209.165.201.2 255.255.255.224
Apopka(config-if)#no shutdown
Apopka(config-if)#exit
6) Configure Serial interface (on the left) of router Apopka:
Using the same method to find out the increment of the Serial network:
Serial network 192.0.2.128/28:
Increment: 16 (/28 = 1111 1111.1111 1111.1111 1111.1111 0000)
Network address: 192.0.2.128 (because 8 * 16 = 128 so 192.0.2.128 is also the network address
of this subnet)
Broadcast address: 192.0.2.143
-> The last assignable host address in this subnet is 192.0.2.142/28.
Assign the last assignable host address to S0/0/0 interface of Apopka router:
Apopka(config)#interface S0/0/0 (or use interface S0/0 if not successful)
Apopka(config-if)#ip address 192.0.2.142 255.255.255.240
Apopka(config-if)#no shutdown
Apopka(config-if)#exit
7) Configure RIP v2 routing protocol:
Apopka(config)#router rip
Apopka(config-router)#version 2
Apopka(config-router)#network 209.165.201.0
Apopka(config-router)#network 192.0.2.128
Apopka(config-router)#end
Save the configuration:
Apopka#copy running-config startup-config
Finally, you should use the ping command to verify all are working properly!
NEW QUESTION # 53
......
Earning the Facebook 100-101: Meta Certified Digital Marketing Associate certification sets a marketer apart, signaling to employers or clients that they are familiar with the latest marketing strategies and techniques. Meta Certified Digital Marketing Associate certification reflects an individual's ability to create and manage successful Facebook Ads campaigns, which translate to revenue for businesses of all sizes. Furthermore, the Facebook 100-101: Meta Certified Digital Marketing Associate certification is an excellent addition to a marketer's resume, making them more marketable in today's competitive job market.
Updated Facebook 100-101 Dumps – PDF & Online Engine: https://www.prepawaypdf.com/Facebook/100-101-practice-exam-dumps.html
PDF Exam Material 2024 Realistic 100-101 Dumps Questions: https://drive.google.com/open?id=1pmPHZiHtKWFiuwO3poFUHsW1QV-FSVMH